TY - JOUR
T1 - Compatibility Assessment of Elastomer Materials to Test Fuels Representing Gasoline Blends Containing Ethanol and Isobutanol
AU - Kass, Michael D.
AU - Theiss, Timothy
AU - Pawel, Steve
AU - Baustian, James
AU - Wolf, Les
AU - Koch, Wolf
AU - Janke, Chris
PY - 2014/6
Y1 - 2014/6
N2 - The compatibility of elastomeric materials used in fuel storage and dispensing applications was determined for test fuels representing neat gasoline and gasoline blends containing 10 and 17 vol.% ethanol, and 16 and 24 vol.% isobutanol. The actual test fuel chemistries were based on the aggressive formulations described in SAE J1681 for oxygenated gasoline. Elastomer specimens of fluorocarbon, fluorosilicone, acrylonitrile rubber (NBR), polyurethane, neoprene, styrene butadiene rubber (SBR) and silicone were exposed to the test fuels for 4 weeks at 60ŶC. After measuring the wetted volume and hardness, the specimens were dried for 20 hours at 60ŶC and then remeasured for volume and hardness. Dynamic mechanical analysis (DMA) was also performed to determine the glass transition temperature (Tg). Comparison to the original values showed that all elastomer materials experienced volume expansion and softening when wetted by the test fuels. The fluorocarbons underwent the least amount of swelling (<25 %) while the SBR and silicone samples exhibited the highest level of expansion (>100%). The level of swelling for each elastomer was higher for the test fuels containing the alcohol additions. In general, ethanol produced slightly higher swell than the oxygen equivalent level of isobutanol. When dried, the fluorocarbon specimens were slightly swollen (relative to the baseline values) due to fuel retention. The NBRs and neoprene exhibited shrinkage and embrittlement associated with the extraction of plasticizers. SBR also experienced shrinkage (after drying) but its hardness returned to the baseline value. The dried volumes (and hardness values) of the silicone, SBR and fluorosilicone rubbers closely matched their original values, but the polyurethane specimen showed degradation with exposure to the test fuels containing ethanol or isobutanol. The DMA results showed that the test fuels effectively decreased Tg for the fluorocarbons, but increased Tg for the NBR materials. The Tg values other elastomers were not affected by the test fuels.
AB - The compatibility of elastomeric materials used in fuel storage and dispensing applications was determined for test fuels representing neat gasoline and gasoline blends containing 10 and 17 vol.% ethanol, and 16 and 24 vol.% isobutanol. The actual test fuel chemistries were based on the aggressive formulations described in SAE J1681 for oxygenated gasoline. Elastomer specimens of fluorocarbon, fluorosilicone, acrylonitrile rubber (NBR), polyurethane, neoprene, styrene butadiene rubber (SBR) and silicone were exposed to the test fuels for 4 weeks at 60ŶC. After measuring the wetted volume and hardness, the specimens were dried for 20 hours at 60ŶC and then remeasured for volume and hardness. Dynamic mechanical analysis (DMA) was also performed to determine the glass transition temperature (Tg). Comparison to the original values showed that all elastomer materials experienced volume expansion and softening when wetted by the test fuels. The fluorocarbons underwent the least amount of swelling (<25 %) while the SBR and silicone samples exhibited the highest level of expansion (>100%). The level of swelling for each elastomer was higher for the test fuels containing the alcohol additions. In general, ethanol produced slightly higher swell than the oxygen equivalent level of isobutanol. When dried, the fluorocarbon specimens were slightly swollen (relative to the baseline values) due to fuel retention. The NBRs and neoprene exhibited shrinkage and embrittlement associated with the extraction of plasticizers. SBR also experienced shrinkage (after drying) but its hardness returned to the baseline value. The dried volumes (and hardness values) of the silicone, SBR and fluorosilicone rubbers closely matched their original values, but the polyurethane specimen showed degradation with exposure to the test fuels containing ethanol or isobutanol. The DMA results showed that the test fuels effectively decreased Tg for the fluorocarbons, but increased Tg for the NBR materials. The Tg values other elastomers were not affected by the test fuels.
UR - http://www.scopus.com/inward/record.url?scp=84903487124&partnerID=8YFLogxK
U2 - 10.4271/2014-01-1462
DO - 10.4271/2014-01-1462
M3 - Article
AN - SCOPUS:84903487124
SN - 1946-3952
VL - 7
SP - 445
EP - 456
JO - SAE International Journal of Fuels and Lubricants
JF - SAE International Journal of Fuels and Lubricants
IS - 2
ER -